Bölüm "Fakülteler, Mühendislik Fakültesi, Makine Mühendisliği Bölümü" Scopus İndeksli Yayınlar Koleksiyonu için listeleme
Toplam kayıt 16, listelenen: 1-16
-
Analysis of wind energy potential; A case study of Kocaeli University campus
(Elsevier Sci Ltd, 2019)Determination of the wind energy potential is achieved by point measurement at the place. MERRA software which is generated by NASA provides the point data values. The point data with using Windographer software gives ... -
CFD modelling and experimental validation of cell performance in a 3-D planar SOFC
(Pergamon-Elsevier Science Ltd, 2019)Fuel cells can be used to provide power for most electrical or electronic devices designed for operation from batteries or from conventional utility power sources. In this study, a three dimensional Computational Fluid ... -
Design of a broadband elastic metamaterial via topologically optimized inertial amplification mechanisms
(European Association for Structural Dynamics, 2020)Elastic metamaterials enable to generate phononic band gaps below the Bragg limit. Most metamaterials in the literature are based on vibration absorption (local resonance) principle. In this study, a two dimensional elastic ... -
Development of a new model for determine of cutting parameters in metal drilling processes
(Springer Heidelberg, 2020)Metal drilling and cutting processes are used commonly in many areas of the industry. When these processes investigated analytically, it is seen that they have a very complicated structure. This complicated structure can ... -
Drying behavior of prina (crude olive cake) using different types of dryers
(Taylor & Francis Inc, 2016)The purpose of this research is to investigate the drying kinetics and determine the suitable drying method of prina, which is obtained after pressing of olives in olive oil factories, and which cannot be used efficiently ... -
Dynamic Modelling, Investigation of Manoeuvring Capability and Navigation Control of a Cargo Ship by using Matlab Simulation
(Elsevier Science Bv, 2016)In this paper a simplified dynamic analysis of a cargo ship using simulation and modelling are presented. Provided with mathematical equations dynamics of ship motion characteristics with several maneuvering capabilities ... -
Effect of temperature on wear behavior of multilayered thin cr-coated acrylonitrile-butadiene-styrene polymer: An experimental and prediction study
(ASTM International, 2022)The wear behavior of thin chromium-coated and uncoated acrylonitrile-butadiene-styrene (ABS) samples were investigated by using a pin-on-disk test apparatus with a heat chamber for different temperatures of 30°C, 50°C, ... -
The Effect of Temperature on Wear Performance of High-Velocity Oxy-Fuel Sprayed WC-10Co-4Cr Coating on AA7075-T6 Substrate
(Springer, 2021)In this study, the friction wear performance of a High-velocity oxy-fuel (HVOF) sprayed WC-10Co-4Cr coated AA7075-T6 substrate was investigated against a WC-4Co ball at different temperatures using a pin-on-disk tribometer. ... -
Effects of infill pattern and density on wear performance of FDM-printed acrylonitrile- butadiene-styrene parts
(Walter De Gruyter Gmbh, 2021)Acrylonitrile-butadiene-styrene test specimens were additively manufactured by fused deposition method to investigate the effects of infill pattern and density on wear rate, coefficient of friction, wear mechanisms, and ... -
An experimental study on wear performance of electrolytic multilayer cu-ni-cr coated abs under different test forces
(TUBITAK, 2021)Plastic materials are widely preferred in many applications due to being light and cheap in addition to being manufactured easily with various manufacturing methods like injection molding or additive manufacturing. One of ... -
Investigation of Tensile, Viscoelastic, and Viscoplastic Behavior of Polylactic Acid Manufactured by Fused Deposition Modeling
(Amer Soc Testing Materials, 2021)Uniaxial tensile and uniaxial loading-unloading experiments are performed to characterize the mechanical properties of polylactic acid (PLA) manufactured by fused deposition modeling (FDM). To investigate viscoelastic and ... -
Modelling of dynamic cutting force coefficients and chatter stability dependent on shear angle oscillation
(Springer London Ltd, 2017)Productivity of high-speed turning operations is limited by the onset of self-excited vibrations known as chatter. Unless avoided, chatter vibrations may cause large dynamic loads damaging the machine spindle, cutting tool ... -
Process damping model approach in milling operations
(Springer Heidelberg, 2021)The subject of this study is a new Process Damping Model approach for milling with flat end milling cutter. Dynamic model of the cutting system was modeled and applied for the milling operation. The machining process is ... -
Realization of an ultrawide stop band in a 2-D elastic metamaterial with topologically optimized inertial amplification mechanisms
(Pergamon-Elsevier Science Ltd, 2020)The aim of this study is to design a two-dimensional solid structure with embedded inertial amplification mechanisms that shows an ultrawide stop band (band gap) at low frequencies. First of all, a unique compliant inertial ... -
Thermoforming of biopolymer-green polyethylene sheets
(ModTech Publishing House, 2018)Thermoforming is a forming technique in which petrochemical-based thermoplastics, biodegradable plastics and also plastic composites can be formed. Due to recent developments in the packaging industry, it was understood ... -
Use of Image Analysis for Non-Destructive Testing of Thermoformed Food Packages
(Walter de Gruyter GmbH, 2021)The aim of this study is to determine the thickness distribution of a food package using a non-destructive method. Initially, thickness measurements were carried out using an experimental procedure for thermoformed samples ...